Cutting machine safety operation

First, the boot

1, open electrical isolation switch (set in the electric control cabinet ago) by EMERCENCY STOP RESET and READY TO RUN button, the key to open the MACHINE RUN (the main operating table) to check the voltage (380V), current is correct and stable.

2, open hydraulic system power switch (set in the main hydraulic drive rack), the main hydraulic drive system for checking the oil level and pressure gauge shows the correct and stable.

3, open air shut-off valve (set to air on the intake manifold under the control cabinet), check the air pressure is correct (not less than 6.0bar), and stability.

Second, the setting control

1, arranged according to single-cut plan the film type, thickness, length, width and other settings cut menu.

2, the lift from the corresponding PDF file BOPP film.

3, set the appropriate size film winding length and width.

4, select the appropriate winding station, adjust the roller arm and roller, installed the appropriate specifications of the paper core.

Third, feeding, clothing and film and then film

1, feeding: in accordance with the requirements of cutting a single program, in accordance with traffic rules, according to the actual situation, hanging shelves in time to take the appropriate Mother volume selection based on the direction of the corona on the outside surface of slitting rewinding the shelves, and use control button clamping steel core, steel core support arms and the left lane.

2, transmembrane: When the cutting machine with no film required to carry out transmembrane. Slitter device by penetrating and function keys, the original film end to the penetrating eye on the link, start wearing a membrane button on the membrane formation along the cut to the distribution process in each roll.

3, then film: When the cutting machine on film roll replacement joints, the use of vacuum then film sets, film sets first then start to work location, the first man to slitting the membrane traction roll flattening and switch on the upper part of vacuum suction membrane, the membrane formation of the adsorbed film in the next stage, labeled double-sided tape and cut off the extra tape under the membrane, the membrane will be unwinding the shelves and started flattening the lower part of vacuum adsorption of the membrane formation, won the belt on the paper layer and the formation of adhesive film, joints should be neat, wrinkle-free, and then turn off the vacuum pump down, the film sets to open access to non-working position.

Fourth, start running

1, changing for the better size, good arm, inner and outer rolling paper core, the pressure roller is running for the state to inform all personnel leave the machine, ready to run.

2, the main operation platform ANTI-STAIC BARS placed in AUTO, READY TO RUN opening, start MACHINE RUN switched.

Fifth, cut control

Operation in cutting process, the careful monitoring of effects observed cutting operation, the cutting speed of unwinding tension, contact pressure and the curved roller, roller traction material side, leading edge and other appropriate regulation and control.

VI, receiving

1, when the inner and outer side rolling stop running when the machine is completed, use the button to unload film unloading in the prepared membrane film of small car, cut the film and a good film with a sealing glue volume.

2, the use of release chuck chuck release the button to check whether to leave the film roll paper core paper core, if one is still stuck in the paper core is used on manually remove the film roll.

3, to ensure that all films on the small car to leave the chuck, the use of loaded film winding button and raised arm, install the appropriate paper core, the film neatly attached to the paper core, and the next cut.

VII, parking

1, when the film runs to set the length of the roll, the device automatically.

2, the device is running, as required according MACHINE STOP parking.

3, when the need to quickly stop, press the MACHINE STOP key is greater than 2S.

4, when there is a state of emergency equipment or man-made accidents, press the EMERGENCY STOP emergency stop.

VIII Notes

1, before starting to ensure that the voltage, current, and the hydraulic equivalent of the right and stable.

2, the device is ready to run, all staff must be notified to leave the equipment to ensure safety before they can start running.

3, cutting in the run-time, should not touch the operation of the film roll or roller core, so as not to cause personal injury involved in the hand.

4, during operation, should not scratch a knife or a hard object, cut each roll core.